Metal Stucco
Accessories
Metal Stucco Accessories
Niles Building Products manufactures a full line of metal stucco accessories
available in both hot-dipped galvanized steel and pure zinc alloy.
Niles Building Products manufactures a full line of metal stucco accessories
available in both hot-dipped galvanized steel and pure zinc alloy.
The #7 FHA Foundation Weep Screed is used to provide a weep mechanism as part of the drainage system as required at the bottom of all framed walls; by all major building codes and the International Building Code in ASTM C1063. The larger holes in the ground flange are drainage holes as the entire surface of the sloped ground provides for drainage once the stucco has hydrated and shrinkage has occurred. The 3-1/2″ nailing flange serves as a flashing when water resistant, breathable building paper or paper backed lath is installed over the flange.
#7 FHA Foundation Weep Screed | crtns/ pallet | nominal lbs/cRtn | nominal wt/pallet** |
---|---|---|---|
1/2″ GALV. 1/2″ ZINC* | 25 25 | 80 82 | 2000 2050 |
5/8″ GALV. 5/8″ ZINC* | 25 25 | 83 86 | 2075 2150 |
3/4″ GALV. 3/4″ ZINC* | 25 25 | 88 91 | 2200 2275 |
7/8″ GALV. 7/8″ ZINC* | 25 25 | 92 96 | 2300 2400 |
1″ GALV. 1″ ZINC* | 25 25 | 96 100 | 2400 2500 |
25 PCS/CRTN – 250 FT/CRTN
*Minimum quantities apply. Consult with sales before ordering.
**Pallet weights may vary.
For additional information, please download our spec sheets:
Sill Screed is used so trowel can access underneath the screed to clean excess stucco material.
#36 Foundation Sill Screed | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet* |
---|---|---|---|
1/2” | 25 | 65 | 1625 |
3/4” | 25 | 75 | 1875 |
7/8” | 25 | 75 | 1875 |
25 PCS/CRTN – 250 FT/CRTN
*Pallet weights may vary.
For additional information, please download our spec sheets:
Wing size 2-5/8″ x 2-5/8″. Used to reinforce external corners in Portland cement stucco applications. The 2-5/8″ expanded flanges allow for complete embedment of the entire bead, especially near the nose where strength is needed most. Available in hot-dipped galvanized and 99% pure zinc alloy.
Niles No. 1-A Corner Bead | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet* |
---|---|---|---|
10’ GALV. 10’ ZINC. | 40 40 | 40 45 | 1600 1800 |
30 PCS/CRTN – 300 FT/CRTN
OTHER LENGTHS AVAILABLE ON A SPECIAL-ORDER BASIS
*Pallet weights may vary.
For additional information, please download our spec sheets:
Wider, reinforced flange of the Niles 2-A Corner Bead provides additional rigidity and strength superior to the Niles 1-A, thus allowing for easier installation.
NILES 2-A CORNER BEAD | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet** |
---|---|---|---|
10’ GALV. 10′ ZINC* | 25 25 | 61 63 | 1525 1575 |
30 PCS/CRTN – 300 FT/CRTN
*Minimum quantities apply. Consult with sales before ordering.
**Pallet weights may vary.
For additional information, please download our spec sheets:
WIRE CORNER BEADS | CRTNS/ PALLET | NOMINAL LBS/CRTN | NOMINAL WT/PALLET* |
---|---|---|---|
Straight 10′ | 24 | 40 | 960 |
Straight Arch 10′ | 24 | 40 | 960 |
Straight Short Flange 10′ | 24 | 40 | 960 |
Bullnose 10′ | 24 | 40 | 960 |
40 PCS/CRTN – 400 FT/CRTN
*Pallet weights may vary.
For additional information, please download our spec sheet:
Used to effectively terminate plaster edge and/or to separate stucco from all other structural membranes at doors, windows and other openings; also when plaster/stucco meets dissimilar material. Expanded flange provides excellent stucco embedment at the junctions of the bead and metal lath.
Also available with punched grounds upon request. Caution: 66X Casing Beads with punched grounds should not be used as a substitute for #7 FHA Foundation Weep Screed in a 3-coat stucco system.
NILES NO. 66X EXPANDED FLANGE | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet* |
---|---|---|---|
1/4″ GALV. 1/4″ ZINC | 42 42 | 41 43 | 1722 1806 |
3/8″ GALV. 3/8″ ZINC | 42 42 | 41 43 | 1722 1806 |
1/2″ GALV. 1/2″ ZINC | 42 42 | 41 43 | 1722 1806 |
5/8″ GALV. 5/8″ ZINC | 42 42 | 48 47 | 2016 1975 |
3/4″ GALV. 3/4″ ZINC | 42 42 | 48 47 | 2016 1975 |
7/8″ GALV. 7/8″ ZINC | 42 42 | 48 51 | 2016 2142 |
1″ GALV. 1″ ZINC | 42 42 | 48 51 | 2016 2142 |
1-1/4″ GALV. 1-1/4″ ZINC | 40 40 | 50 54 | 2000 2160 |
1-3/8″ GALV. 1-3/8″ ZINC | 40 40 | 55 61 | 2200 2440 |
1-1/2″ GALV. 1-1/2″ ZINC | 40 40 | 55 61 | 2200 2440 |
30 PCS/CRTN – 300 FT/CRTN
*Pallet weights may vary.
For additional information, please download our spec sheets:
The choice where short, solid flanges are preferable.
Also available with punched grounds.
NILES NO. 66N SHORT FLANGE | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet** |
---|---|---|---|
3/8“ GALV. 3/8“ ZINC* | 42 42 | 41 43 | 1722 1806 |
1/2“ GALV. 1/2“ ZINC* | 42 42 | 41 43 | 1722 1806 |
3/4“ GALV. 3/4“ ZINC* | 42 42 | 48 47 | 2016 1975 |
7/8“ GALV. 7/8“ ZINC* | 42 42 | 48 51 | 2016 2142 |
1” GALV. 1” ZINC* | 42 42 | 48 51 | 2016 2142 |
1-1/4“ GALV. 1-1/4“ ZINC* | 40 40 | 50 54 | 2000 2160 |
1-1/2“ GALV. 1-1/2“ ZINC* | 40 40 | 55 61 | 2200 2440 |
30 PCS/CRTN – 300 FT/CRTN
*Special order only. Minimum quantities apply.
**Pallet weights may vary.
For additional information, please download our spec sheets:
The choice where longer, solid flanges are preferable.
Also available with punched grounds (J-Weep).
NILES NO. 66N LONG FLANGE | CRTNS/ PALLET | NOMINAL LBS/CRTN | NOMINAL WT/PALLET* |
---|---|---|---|
3/8″ | 42 | 67 | 2814 |
1/2“ | 42 | 75 | 3150 |
5/8″ | 42 | 78 | 3276 |
3/4“ | 42 | 78 | 3276 |
7/8“ | 42 | 81 | 3402 |
1” | 42 | 82 | 3444 |
1-3/8“ | 40 | 86 | 3440 |
1-1/2“ | 40 | 86 | 3440 |
30 PCS/CRTN – 300 FT/CRTN
*Special orders only. Minimum quantities apply.
For additional information, please download our spec sheets:
Niles Double ‘V’ Expansion Control Joints are used to provide mechanism for movement to accommodate expansion and contraction caused by initial stucco shrinkage and minor thermal movement.
DOUBLE ‘V’ EXPANSION CONTROL JOINT | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet* |
---|---|---|---|
1/4“ GALV. 1/4“ ZINC | 42 42 | 37 39 | 1554 1638 |
3/8“ GALV. 3/8“ ZINC | 42 42 | 37 39 | 1554 1638 |
1/2“ GALV. 1/2“ ZINC | 40 40 | 52 54 | 2080 2160 |
5/8“ GALV. 5/8“ ZINC | 40 40 | 55 57 | 2200 2280 |
3/4“ GALV. 3/4“ ZINC | 40 40 | 68 71 | 2720 2840 |
7/8“ GALV. 7/8“ ZINC | 40 40 | 70 72 | 2800 2880 |
24 PCS/CRTN – 240 FT/CRTN
*Pallet weights may vary.
For additional information, please download our spec sheets:
Similar to the standard Double ‘V’, Niles Double ‘V’ Inside Corner Expansion Control Joint is roll formed to fit inside corner locations.
DOUBLE ‘V’ INSIDE CORNER EXPANSION CONTROL JOINT | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet* |
---|---|---|---|
1/2“ GALV. 1/2“ ZINC | 40 40 | 52 54 | 2080 2160 |
5/8“ GALV. 5/8“ ZINC | 40 40 | 55 57 | 2200 2280 |
3/4“ GALV. 3/4“ ZINC | 40 40 | 68 71 | 2720 2840 |
7/8“ GALV. 7/8“ ZINC | 40 40 | 70 72 | 2800 2880 |
24 PCS/CRTN – 240 FT/CRTN
*Pallet weights may vary.
For additional information, please download our spec sheets:
Like the Double ‘V’, the Double ‘J’ is also used to provide a mechanism for movement to accommodate expansion and contraction caused by initial stucco shrinkage and minor thermal movement. The Double ‘J’-shaped shoulders provide a more secure stucco bond. Comes pre-taped to ensure a clean finish.
DOUBLE ‘J’ EXPANSION CONTROL JOINT | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet** |
---|---|---|---|
1/2“ GALV. 1/2“ ZINC* | 40 40 | 68 71 | 2720 2840 |
3/4“ GALV. 3/4“ ZINC* | 40 40 | 69 72 | 2760 2880 |
7/8“ GALV. 7/8“ ZINC* | 40 40 | 80 79 | 3200 3160 |
24 PCS/CRTN – 240 FT/CRTN
*Special order only. Minimum quantities apply.
**Pallet weights may vary.
For additional information, please download our spec sheets:
Niles Zinc Control Joint is used to provide a mechanism for movement to accommodate expansion and contraction caused by initial stucco shrinkage and minor thermal movement. The ‘J’-shaped shoulder provides excellent stucco bonding.
NILES ZINC CONTROL JOINT | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet* |
---|---|---|---|
C380 – 3/8“ | 20 | 63 | 1260 |
C500 – 1/2“ | 20 | 65 | 1300 |
C750 – 3/4“ | 20 | 75 | 1500 |
25 PCS/CRTN – 250 FT/CRTN
*Pallet weights may vary.
For additional information, please download our spec sheet:
The Niles Two-Piece Tru-Joint is used to relieve stress caused by expansion and contraction and initial stucco shrinkage. The opening adjusts from 1/4″ to 5/8″ and is ideally used where more movement is expected than would be normal with a one-piece expansion control joint.
NILES TWO-PIECE TRU-JOINT | CRTNS/ Pallet | Nominal LBS/CRTN | Nominal WT/Pallet* |
---|---|---|---|
1/2“ GALV. 1/2“ ZINC | 25 25 | 64 66 | 1600 1650 |
3/4“ GALV. 3/4“ ZINC | 25 25 | 68 67 | 1700 1675 |
7/8“ GALV. 7/8“ ZINC | 25 25 | 72 71 | 1800 1775 |
15 PCS/CRTN – 150 FT/CRTN
*Pallet weights may vary.
For additional information, please download our spec sheets:
The M-Slide Two-Piece Expansion Joint is manufactured for applications where movement is anticipated. The two-piece design allows for 1-inch vertical movement while allowing water to egress from the wall.
Manufactured from G-90 coated material.
M-Slide Two-Piece Expansion Joint | PCS/ CRTN | LBS/ CRTN |
---|---|---|
7/8” | 10 | 50 |
100 FT/CRTN
For additional information, please download our spec sheet:
Used to reinforce and straighten inside metal lath installations to provide strength and smoothness to this critical area.
NILES CORNERITE | PCS/ CRTN | FT/ CRTN | CRTNS/ PALLET | NOMINAL LBS/CRTN | NOMINAL WT/PALLET* |
---|---|---|---|---|---|
2” GALV. 4’ | 150 | 600′ | 18 | 57 | 1026 |
2” GALV. 8’ | 75 | 600′ | 18 | 57 | 1026 |
3” GALV. 8’ | 75 | 600′ | 18 | 76 | 1368 |
*Pallet weights may vary.
For additional information, please download our spec sheet:
NILES STRIP LATH | PCS/ CRTN | FT/ CRTN | CRTNS/ PALLET | NOMINAL LBS/CRTN | NOMINAL WT/PALLET* |
---|---|---|---|---|---|
4” GALV. 8′ | 75 | 600′ | 18 | 56 | 1008 |
6” GALV. 8’ | 75 | 600′ | 18 | 76 | 1368 |
*Pallet weights may vary.
For additional information, please download our spec sheet:
Niles Building Products, an industry leader in expanded metal and vinyl building accessories, with manufacturing facilities in Niles, OH, Grand Prairie, TX and Jacksonville, FL.
1600 Hunter Street, Niles OH 44446
Phone: (800) 323-3329
2303 I-30 Frontage Road Ste 100 Grand Prairie, TX 75050
Phone: (972) 522-1556
8441 Western Way, Jacksonville, FL 32256
Phone: (904) 374-7183